L-shaped countertop with island
White countertop with an island, wall panel and baseboards. The side legs meet the floor with invisible joints — full cycle from measurement to installation.
RoleFull cycle: measurement → installation
Acrylic solid surface · Corian
Roman Simankov
I make objects and parts from acrylic solid surface — from measurement to installation.
ScrollA little about me
About
I make objects from acrylic solid surface — countertops, reception desks, bar counters, cladding. I work the full cycle, from measurement to installation. I read technical drawings and am comfortable on a site and in a workshop. Looking for steady work — including abroad.
Roman3+ years of experience
6 areas of work
16 projects in this selection
Selected work
Projects
Sixteen jobs in three groups — from private interiors to federal-scale sites.
Fabrication 10
Reception desk at a private school
Acrylic stone on the corner and perimeter cladding and on the reception tabletop. The hard part was gluing thin cladding panels precisely, on site.
RoleInstallation
Buffet counters at Hotel Slavyanka
A breakfast bar over 11 meters long and 800 mm wide. Several sections glued on site, with technical cutouts for warmers and outlets.
RoleFabrication + installation
L-shaped countertop with radius forms
A 90-degree radius bend near the sink and a radius on the open edge. Integrated acrylic sink with drip grooves.
RoleProduction + installation
Bar counter with a leg
The leg of the counter bends smoothly at 90 degrees, with a 30 cm radius on the return. The 40 mm edge holds a constant thickness along the whole curve.
RoleFabrication
Bathroom countertop with a chamfer transition
Small but geometrically tricky: a chamfer transition on the plinth, a step in the middle plane, and the same chamfer kept on the step.
RoleMeasurement + fabrication
Chessboard top for a cabinet
A chessboard surface made from two kinds of stone. The real task was assembling it so the squares never shift.
RoleMeasurement, fabrication, installation
Multi-level U-shaped drinks countertop, hotel
Over 5 m², several levels, wrapping around a central column. I plan the on-site assembly to keep installation time down.
RoleFabrication + installation
Multi-level straight drinks countertop
A simpler shape, but with a two-tier overhang. Designed for quick installation on site.
RoleFabrication + installation
Boat-shaped reception desk
A reception desk with two curved sides of 4 m radius, a cutout for the operator's legs and a drawer compartment.
RoleFabrication
Repair 3
U-shaped countertop — repair
Full demount, reinforcement, crack repair, re-gluing and polishing — all at the client's home, with no trip to the workshop.
RoleRepair on site
Removing a chemical burn
A deep chemical burn in the surface. Coarse grit took off the damaged layer — underneath was pristine stone.
RoleBurn removal and restoration
Crack repair in the flat
An inlay for the crack, cut from discontinued stone matched out of warehouse stock. After polishing, the joint is indistinguishable from the surface.
RoleCrack repair with material matching
Large projects 3
Lakhta Center — staircase
Cladding for the curved staircase at the Lakhta Center. Large curved plates, mounted at heights of 0–10 meters, with a crew of dozens.
RoleInstallation and grinding
Lakhta Center — flower beds
Flower bed cladding in acrylic stone across the Lakhta Center complex.
RoleInstallation and grinding
Wine City «White Cape»
The demonstration project that led to cladding the whole complex. The client compared several manufacturers and chose our work.
RoleDemonstration project → full contract
What I can do
What I can do
Six areas of work — from the first measurement to ongoing consultations on the material.
- 01
Measurement
I come to the site, take precise dimensions, check the geometry and load-bearing surfaces. Based on measurements I create a cutting plan — accounting for joints, edges, and installation order so that there are minimal extra operations on site.
- 02
Fabrication
Cutting according to the layout, edge profiling and radii, gluing parts into a single unit, thermoforming complex shapes. I control every detail — precision at this stage determines the final result.
- 03
Installation
Installing the object on site with fit adjustment, final tightening of joints and edges. Handover to the client with a quality check together.
- 04
Repair
Fixing cracks, scratches, chips and chemical damage. Restoring the surface to factory condition — grinding, inlay, polishing. I work both on site and in the workshop.
- 05
Maintenance
Periodical polishing, coating renewal, removing dull spots, replacing hardware. I help keep objects looking perfect for years — as the material deserves, since it doesn't lose its appearance for decades.
- 06
Consultations
I advise on how to properly use acrylic stone objects: about possible problems, ways to solve them, and the advantages of the material. I help choose the surface type, shape, and hardware for your needs — so the result lasts and keeps you happy.
Get in touch
Contact
Open to opportunities — write to me, I reply quickly.